VintageCB750, au service des motocyclistes CB depuis 2010

À propos Pourquoi nous choisir? Avis clients Livraison Retours Nous joindre
Favoris
0 Panier

Votre panier est vide.

Parcourir toutes les pièces
Total (USD): $0.00
Voir le panier
Menu
Rechercher
Favoris
Panier 0
Ma moto Choisissez votre modèle Honda CB

Rechercher des pièces

Recherche dans toutes les pièces Honda CB

Exemple : oil filter (filtre à huile) ou une référence OEM.

1979 Honda CB400TIZ — Clignotants, supports, cabochons et réflecteurs

A bent front stay, deteriorated rear mounting rubbers and a damaged lens seal call for different turn-signal parts on the 1979 Hawk I. Start at the mounting position or lamp being repaired, then match the stay length, rubber quantity or gasket to that assembly.

Fermer ×
Votre moto enregistrée Choisissez votre modèle Honda CB

Magasiner par catégorie

La plupart des commandes sont expédiées le jour ouvrable même ou le suivant Garantie de compatibilité Pièce répertoriée pour votre modèle et votre année? Si elle ne convient pas comme indiqué, nous trouverons une solution. Soutien technique Demandez à notre équipe de vous aider à choisir la bonne pièce Honda CB.
Consultation en cours Clignotants, supports, cabochons et réflecteurs

Pièces pour motos Honda

Choisissez votre modèle et l’année pour voir les pièces répertoriées pour votre moto.

Honda CB750 CB550 CB500 CB400 CB360 front turn signal stay

Honda CB Front Turn Signal Stay

$12.95 USD
11-2167
Replace a damaged front signal stay with this Front Signal Lamp Stay in chrome. Body length 65mm, thread 25mm, total length 90mm. Pairs with...
Honda CB750 CB500 CB450 CB400 turn signal lamp gasket 33443-268-671

Honda CB Turn Signal Lamp Gasket ~ Replaces 33443-268-671

$4.61 USD
11-2085
Service your early CB750 or classic twin turn signal with this Turn Signal Lamp Gasket, replacing OEM #33443-268-671. Pairs with our signal lens #11-2110...
Honda CB750 CB550 CB450 CB400 rear turn signal rubbers pk 2 33606-371-000

Honda CB750 / CB550 / CB450 / CB400 Rear Turn Signal Rubbers Pk/2 ~ Replaces 33606-371-000

$15.95 USD
73-0834
Replace your rear turn signal rubbers with this Rear Turn Signal Rubbers Pk/2, replacing OEM #33606-371-000. These are the rubbers that go under the...
Comparer

1979 Honda CB400TI Hawk I · Turn-Signal Mounts & Seals Buying guide

Match the signal repair to its mounting position

The front stay has a defined length; the rear rubbers are packed by the needs of one signal. A lens gasket should be compared with the lamp fitted, especially after an aftermarket conversion.

Parts to consider

Honda CB Front Turn Signal Stay Chrome front signal stay65 mm body and 25 mm threaded section give a 90 mm overall length. Compare the stay currently fitted.Voir la pièce Honda CB750 / CB550 / CB450 / CB400 Rear Turn Signal Rubbers Pk/2 ~ Replaces 33606-371-000 Rear signal mounting rubbersTwo rubbers per pack; each rear signal uses two. One pack services one rear signal mounting position.Voir la pièce Honda CB Turn Signal Lamp Gasket ~ Replaces 33443-268-671 Turn-signal lens gasketReplacement gasket for reference 33443-268-671. Match the existing lamp and lens before ordering.Voir la pièce

Use the full stay measurement

The front stay has a 65 mm body plus a 25 mm threaded section, making 90 mm overall. Compare those separate measurements with the removed stay. Measuring only the exposed chrome portion can make a different-length mounting look like the right replacement.

Count rubber packs by rear signal

Each rear signal uses two mounting rubbers, and each pack contains two. Replacing the rubbers at both rear signals therefore calls for two packs. A lamp gasket is a separate selection, so inspect the lens sealing area as well as the mounting rubber.

Common buying questions

Is one pack of rear rubbers enough for both turn signals?

One pack contains the two rubbers needed at one rear signal. For both rear signals, order two packs. This count refers to the mounting rubbers, so check any other damaged signal components separately.

Can the front stay be chosen using its overall length alone?

Compare all three listed dimensions: 65 mm body, 25 mm thread and 90 mm total. Matching only the total can miss a different split between the exposed body and the portion that passes through the mounting.

Will the gasket seal a small aftermarket signal?

Check the actual lamp and lens. The gasket corresponds to reference 33443-268-671 and a specific stock-style lamp arrangement; that does not establish a match for a smaller replacement housing or a differently shaped sealing groove.

Vous ne savez pas quelle pièce choisir ?

Envoyez-nous le modèle et l’année de votre moto, des photos de la pièce actuelle et les détails de toute modification par rapport au montage d’origine.

Poser une question sur la compatibilité
Catégories de pièces pour 1979 Honda CB400TIZ

Votre panier

×