VintageCB750, au service des motocyclistes CB depuis 2010

À propos Pourquoi nous choisir? Avis clients Livraison Retours Nous joindre
Favoris
0 Panier

Votre panier est vide.

Parcourir toutes les pièces
Total (USD): $0.00
Voir le panier
Menu
Rechercher
Favoris
Panier 0
Ma moto Choisissez votre modèle Honda CB

Rechercher des pièces

Recherche dans toutes les pièces Honda CB

Exemple : oil filter (filtre à huile) ou une référence OEM.

1986 Honda CB700SC — Tubes, ressorts, joints et soufflets de fourche

Choose fork seals for the 1986 CB700SC from the fitted fork and the wear found. The oil-seal set has stated dimensions, while the separate dust pack contains two seals. Inspect the tubes and sealing areas before ordering, particularly if a front-end change has altered the original application.

Fermer ×
Votre moto enregistrée Choisissez votre modèle Honda CB

Magasiner par catégorie

La plupart des commandes sont expédiées le jour ouvrable même ou le suivant Garantie de compatibilité Pièce répertoriée pour votre modèle et votre année? Si elle ne convient pas comme indiqué, nous trouverons une solution. Soutien technique Demandez à notre équipe de vous aider à choisir la bonne pièce Honda CB.
Consultation en cours Tubes, ressorts, joints et soufflets de fourche

Pièces pour motos Honda

Choisissez votre modèle et l’année pour voir les pièces répertoriées pour votre moto.

Honda CB700SC fork seal set

1984-86 Honda CB700SC Fork Seals

$23.45 USD
27-1034
Replace your CB700SC Nighthawk fork seals with this Fork Seal Set, 39 x 51 x 8 / 10mm. Made in Japan by OEM supplier.Key...
Honda CB700SC fork dust seal set

1984-86 Honda CB700SC Fork Dust Seal Set

$22.26 USD
27-1062
Replace your CB700SC Nighthawk fork dust seals with this Fork Dust Seal Set of 2. OEM-quality parts made in Japan.Key Features• Fork dust seal...
Comparer

1986 Honda CB700SC · Fork Seals & Dust Seals Buying guide

Inspect the fork before choosing new oil and dust seals

The original 1986 CB700SC has air-assisted forks and TRAC anti-dive. Its oil seals and outer dust seals are separate pairs. Order by the fitted fork and inspect the tubes before assuming that replacement rubber completes the job.

Parts to consider

1984-86 Honda CB700SC Fork Seals CB700SC fork oil-seal setTwo oil seals, 39 × 51 × 8/10 mm, for the original 1984–86 CB700SC forks; made in Japan by an OEM supplier.Voir la pièce 1984-86 Honda CB700SC Fork Dust Seal Set Fork dust-seal pairTwo dust seals per pack, listed specifically for the CB700SC.Voir la pièce

Compare the oil-seal application

The oil-seal set explicitly includes the CB700SC and provides dimensions. Compare those with the removed seals if the fork identity is uncertain. A similar-looking Nighthawk front end or an unchanged frame does not establish what seals a replacement fork requires.

Plan for the air-assisted fork assembly

Honda warns that the fork caps remain spring-loaded after the air pressure is released. Use the model-specific disassembly procedure and suitable protection rather than treating cap removal as a routine unscrewing job. During reassembly, keep the separate left/right fluid specifications with their respective legs.

Buying questions

Why are oil seals and dust seals separate purchases?

The oil-seal set contains two oil seals; the dust-seal pack contains two outer dust seals. They serve different positions, so replacing both types on both original fork legs calls for one set of each rather than two of either listing.

Can both fork legs be refilled using one generic quantity?

No. Honda gives different fluid quantities and levels for the CB700SC’s right and left forks. Use the model-specific procedure and keep each side identified through service, even though the replacement oil seals share one size.

What if the tubes are damaged where the seals run?

Assess the damaged surfaces with the correct service information before fitting fresh seals. New rubber alone cannot correct a worn or damaged component that prevents proper sealing.

Vous ne savez pas quelle pièce choisir ?

Envoyez-nous le modèle et l’année de votre moto, des photos de la pièce actuelle et les détails de toute modification par rapport au montage d’origine.

Poser une question sur la compatibilité
Catégories de pièces pour 1986 Honda CB700SC

Votre panier

×