VintageCB750, au service des motocyclistes CB depuis 2010

À propos Pourquoi nous choisir? Avis clients Livraison Retours Nous joindre
Favoris
0 Panier

Votre panier est vide.

Parcourir toutes les pièces
Total (USD): $0.00
Voir le panier
Menu
Rechercher
Favoris
Panier 0
Ma moto Choisissez votre modèle Honda CB

Rechercher des pièces

Recherche dans toutes les pièces Honda CB

Exemple : oil filter (filtre à huile) ou une référence OEM.

1985 Honda CB700SC — Flotteurs et composants de carburateur

The float and drain screw serve different parts of the 1985 CB700SC carburetor. Decide whether the repair needs a float with pin, a complete drain screw with O-ring or just drain seals. Compare the existing components before combining overlapping service pieces in one order.

Fermer ×
Votre moto enregistrée Choisissez votre modèle Honda CB

Magasiner par catégorie

La plupart des commandes sont expédiées le jour ouvrable même ou le suivant Garantie de compatibilité Pièce répertoriée pour votre modèle et votre année? Si elle ne convient pas comme indiqué, nous trouverons une solution. Soutien technique Demandez à notre équipe de vous aider à choisir la bonne pièce Honda CB.
Consultation en cours Flotteurs et composants de carburateur

Pièces pour motos Honda

Choisissez votre modèle et l’année pour voir les pièces répertoriées pour votre moto.

Honda CB1100 CB1000 CB900 CB750 float bowl drain screw o-rings pk 4

Honda CB Float Bowl Drain Screw O-Rings Pk/4

$5.80 USD
48-0792
Replace your float bowl drain screw O-rings with this Float Bowl Drain Screw O-Rings 4-Pack.Key Features• Float bowl drain screw O-rings• 4 per packFitment...
Honda CB1100 CB1000 CB900 CB750 float bowl drain screw -a

Honda CB Stock Type Float Bowl Drain Screw ~-A

$6.50 USD
48-5042
Small part, but an important one. This float bowl drain screw with included O-ring allows you to properly drain the carburetor bowl without leaks,...
Honda CB1100 CB1000 CB900 CB750 float bowl drain screw

Honda CB Stock Type Float Bowl Drain Screw

$6.50 USD
48-5042
Replace your stock-type float bowl drain screw with this Float Bowl Drain Screw with O-Ring for the later DOHC and Nighthawk lineup.Note: sold each,...
Nouveau
Épuisé
Honda CB700SC CB650SC CB550SC carb float 16013-KR3-980

Honda Nighthawk Carb Float with Pin ~ Replaces 16013-KR3-980

$19.95 USD
07-4650
Rebuild your Nighthawk's carburetor with this Carb Float with Pin, replacing OEM #16013-KR3-980 / #16013-MA6-003. A critical float for proper fuel metering on the...
Comparer

1985 Honda CB700SC · Floats & Bowl-Drain Parts Buying guide

Check the float, inlet valve and drain as separate faults

The 1985 CB700SC float controls the bowl’s fuel level through the inlet valve. It does not seal the bowl drain. Inspect the actual leaking or damaged area before choosing a float-and-pin assembly, a drain screw or drain O-rings.

Parts to consider

Honda CB Stock Type Float Bowl Drain Screw Float-bowl drain screwSold individually with an O-ring; the CB700SC application is specifically 1984–85.Voir la pièce Honda CB Float Bowl Drain Screw O-Rings Pk/4 Four drain-screw O-ringsFour float-bowl drain-screw O-rings, listed for the 1984–85 CB700SC.Voir la pièce Honda Nighthawk Carb Float with Pin ~ Replaces 16013-KR3-980 Carburetor float with pinFloat and pin replacing references 16013-KR3-980 and 16013-MA6-003.Voir la pièce

The float-level check is a replacement decision

Honda specifies 18.5 mm with the float tang just contacting the float valve. If the assembly is outside specification, the manual calls for replacement rather than a tang-bending adjustment. The selected float includes its pivot pin and lists references 16013-KR3-980 and 16013-MA6-003. Inspect the needle and its seat independently before assuming a new float will stop flooding.

Locate the source of a bowl leak

A leaking drain screw can involve its O-ring, screw tip or the bowl seat. A float or inlet-valve fault instead affects fuel entering the bowl. The selected drain screw is sold individually with an O-ring; the separate O-ring pack contains four. Both drain-part applications cover 1984–85 only, even though the float itself covers 1984–86.

Buying questions

Can an incorrect CB700SC float height be corrected by bending the tang?

The factory procedure specifies 18.5 mm with the tang just touching the float valve, then replacement of the float assembly if it is out of specification. Do not substitute a generic tang-bending procedure. Check valve condition and the measuring position before condemning the float.

Will replacing the float cure a leaking drain screw?

A float controls incoming fuel level; the drain screw and its sealing surfaces are a separate location. Inspect the screw, O-ring and bowl seat when fuel leaks there. The float package supplies a float and pin, not a drain screw, O-ring, inlet needle or seat.

Do new drain screws also need the separate four-pack of O-rings?

Each selected screw already includes its O-ring. The four-pack is useful when the screws are serviceable and only their seals need renewal. A replacement O-ring cannot correct damaged threads, a damaged screw tip or a damaged bowl seat.

Vous ne savez pas quelle pièce choisir ?

Envoyez-nous le modèle et l’année de votre moto, des photos de la pièce actuelle et les détails de toute modification par rapport au montage d’origine.

Poser une question sur la compatibilité
Catégories de pièces pour 1985 Honda CB700SC

Votre panier

×