VintageCB750, au service des motocyclistes CB depuis 2010

À propos Pourquoi nous choisir? Avis clients Livraison Retours Nous joindre
Favoris
0 Panier

Votre panier est vide.

Parcourir toutes les pièces
Total (USD): $0.00
Voir le panier
Menu
Rechercher
Favoris
Panier 0
Ma moto Choisissez votre modèle Honda CB

Rechercher des pièces

Recherche dans toutes les pièces Honda CB

Exemple : oil filter (filtre à huile) ou une référence OEM.

1972 Honda CB350F0 Supersport — pièces de moto

For a CB350F0 cockpit refresh, start with the grip dimensions and the controls actually fitted. The verified choice here is a factory-style closed-end rubber grip set for 7/8-inch handlebars, suited to an original-looking finish after a careful fit check.

Fermer ×
Votre moto enregistrée Choisissez votre modèle Honda CB

Magasiner par catégorie

La plupart des commandes sont expédiées le jour ouvrable même ou le suivant Garantie de compatibilité Pièce répertoriée pour votre modèle et votre année? Si elle ne convient pas comme indiqué, nous trouverons une solution. Soutien technique Demandez à notre équipe de vous aider à choisir la bonne pièce Honda CB.
Consultation en cours Guidon et commandes

Pièces pour motos Honda

Choisissez votre modèle et l’année pour voir les pièces répertoriées pour votre moto.

Type closed-end grips end detail 53165-342-670

Honda OEM Type Closed-End Grips ~ Replaces 53165-342-670

$17.95 USD
02-2423
Take your early-'70s Honda back to factory spec with these Honda OEM-Type Rubber Grips. Faithful replicas of the original factory grips, in black closed-end...
Honda CB400F CB350F handlebar stock type CB400F 1975-76 53100-377-000

1972-77 Honda CB400F / CB350F Handlebar ~ Stock Type ~ CB400F 1975-76 ~ Replaces 53100-377-000

$69.95 USD
73-1101
Replace your CB400F handlebar with this Stock Type Handlebar for the CB400F (1975-76), Chrome. The holes are pre-cut for routing the wiring from the...
Comparer

1972 Honda CB350F0 · Handlebar Grips Buying guide

Renew the hand-contact surfaces around existing controls

The black rubber grips have a 135mm stated length and a closed-end design. Compare the current bars, throttle sleeve and available grip space before ordering, especially if the cockpit has aftermarket controls or bar-end fittings.

Parts to consider

Honda OEM Type Closed-End Grips ~ Replaces 53165-342-670 Closed-end black rubber gripsFactory-style replica grips for 7/8-inch handlebars, 135mm long.Voir la pièce

Compare the complete grip area

Measure the space occupied by each existing grip, including the throttle sleeve and control housing relationship. The replacement grips are specified at 135mm long. A different bar or switch arrangement can change the available space, so compare the assembled cockpit before choosing original-style rubber.

Choose the closed-end appearance deliberately

These grips are black, factory-style replicas with closed ends. That finish suits a stock-looking cockpit, while existing bar-end accessories warrant a separate fit assessment. Confirm that the throttle can operate correctly after installation using the appropriate service procedure.

Buying questions

Are these genuine Honda grips?

They are described as OEM-type replicas rather than genuine Honda parts. They reproduce the black closed-end style, with a stated 135mm length and 7/8-inch handlebar application; choose them with that origin and specification in mind.

Can I use them with bar-end mirrors?

Their ends are closed. Compare your mirror mounting arrangement before ordering, because a bar-end accessory may need a different grip-end configuration. The listed original-style application does not verify a custom mirror installation.

What should I check on the throttle side?

The 7/8-inch application identifies the handlebar size. Compare the fitted throttle sleeve and available grip length separately, including space beside the control housing. Aftermarket throttle assemblies require their own grip-fit check rather than assuming the bar diameter settles both sides.

Vous ne savez pas quelle pièce choisir ?

Envoyez-nous le modèle et l’année de votre moto, des photos de la pièce actuelle et les détails de toute modification par rapport au montage d’origine.

Poser une question sur la compatibilité
Catégories de pièces pour 1972 Honda CB350F0

Votre panier

×