VintageCB750, au service des motocyclistes CB depuis 2010

À propos Pourquoi nous choisir? Avis clients Livraison Retours Nous joindre
Favoris
0 Panier

Votre panier est vide.

Parcourir toutes les pièces
Total (USD): $0.00
Voir le panier
Menu
Rechercher
Favoris
Panier 0
Ma moto Choisissez votre modèle Honda CB

Rechercher des pièces

Recherche dans toutes les pièces Honda CB

Exemple : oil filter (filtre à huile) ou une référence OEM.

1981 Honda CB750K — Outils pour moteur, direction et embrayage

The available service tools cover alternator-rotor removal, clutch-center nuts, an aftermarket spin-on filter and fork-seal fitting. Choose by the installed component and the tool’s interface. The chain-adjuster stopper in this selection is replacement hardware, rather than a removal tool.

Fermer ×
Votre moto enregistrée Choisissez votre modèle Honda CB

Magasiner par catégorie

La plupart des commandes sont expédiées le jour ouvrable même ou le suivant Garantie de compatibilité Pièce répertoriée pour votre modèle et votre année? Si elle ne convient pas comme indiqué, nous trouverons une solution. Soutien technique Demandez à notre équipe de vous aider à choisir la bonne pièce Honda CB.
Consultation en cours Outils pour moteur, direction et embrayage

Pièces pour motos Honda

Choisissez votre modèle et l’année pour voir les pièces répertoriées pour votre moto.

Honda CB1100 CB1000 CB900 CB750 CB450 alternator rotor puller

Honda CB Alternator Rotor Puller

$12.95 USD
35-0035
Pull your DOHC CB alternator rotor with this Alternator Rotor Puller, 18mm x M1.5 right-hand thread, for internal-thread rotors and flywheels.Key Features• Alternator rotor...
Honda CB1100 CB1000 CB900 CB750 CB450 clutch center nut removal tool

Honda CB Clutch Center Nut Removal Tool

$15.10 USD
35-0051
Remove your clutch center nut without damage with this Clutch Center Nut Removal Tool, the perfect tool for easier removal and fitting without damaging...
Honda CB1100 CB1000 CB900 CB750 clutch center nut removal tool premium

Honda CB Clutch Center Nut Removal Tool ~ Premium

$26.95 USD
35-0076
Remove clutch center nuts on different bikes with this Premium Clutch Center Nut Removal Tool, the perfect tool for easier removal and fitting without...
Honda CB1100 CB1000 CB900 CB750 oil filter wrench

Honda CB1100/CB1000/CB900/CB750 Oil Filter Wrench

$14.95 USD
35-9022
Remove and install spin-on oil filters with this 3/8" Drive Tripod Oil Filter Wrench. Designed for our aftermarket spin-on cartridge oil filters.Key Features• 3/8"...
Honda CB750 CB650 CB550 CB500 35 36mm fork seal driver

Honda CB750 / CB650 / CB550 / CB500 35/36mm Fork Seal Driver

$49.95 USD
35-4299
Install 35mm or 36mm fork seals cleanly with this 35/36mm Fork Seal Driver. High-quality carbon steel with split design. Use for easy installation of...
Comparer

1981 Honda CB750K · Engine, Steering & Clutch Tools Buying guide

Compare working ends as well as drive sizes

Two clutch tools offer different drive arrangements. The rotor puller has its own threaded application, while the filter wrench and seal driver depend on the filter or fork equipment being serviced.

Parts to consider

Honda CB Alternator Rotor Puller DOHC alternator rotor pullerThe listing describes an 18mm right-hand internal-thread application for CB750K 1979–82 rotors. Confirm the complete thread specification with the seller.Voir la pièce Honda CB Clutch Center Nut Removal Tool Three-eighths-drive clutch toolThe standard listing specifies a 24mm inside diameter and use with a 3/8-inch driver.Voir la pièce Honda CB Clutch Center Nut Removal Tool ~ Premium Double-ended clutch nut toolThe premium listing specifies 20mm and 24mm ends and a half-inch drive arrangement. Compare the required end with your installed nut.Voir la pièce

Pièces connexes : Tripod wrench for aftermarket spin-on filters · Split 35/36mm fork-seal driver

Do not infer the job from the tool’s name

The oil-filter wrench listing specifically refers to the seller’s aftermarket spin-on cartridge filters. It does not establish that the wrench fits an original filter housing. Likewise, a fork-seal driver is selected for the fork being worked on; the listing states 35mm forks for CB750K 1979–82.

Compare the two clutch-tool formats

The standard clutch tool has a 24mm inside diameter and uses a 3/8-inch driver. The premium version lists 20mm and 24mm ends with a half-inch drive arrangement. Select the interface you need, and read the listing rather than assuming the two products have identical contents or connections.

Common questions

Which rotor puller is listed for the 1981 CB750K?

The puller’s description lists CB750K 1979–82 alternator rotors and an 18mm right-hand internal-thread application. Its thread notation needs clarification, so confirm the complete specification with the seller before comparing it with the installed rotor.

Can the filter wrench be used on any oil-filter setup?

The listing identifies aftermarket spin-on cartridge filters as its application. That is narrower than every filter arrangement used on a CB750. Identify your installed filter and review its listing before choosing this wrench.

Does the 35/36mm driver listing mean this CB750K uses either fork size?

The driver accommodates 35mm or 36mm fork seals, but its CB750K 1979–82 application specifically states 35mm forks. The tool’s wider size coverage is not evidence of a second factory fork size for this motorcycle. Check the fitted fork if it has been replaced.

Vous ne savez pas quelle pièce choisir ?

Envoyez-nous le modèle et l’année de votre moto, des photos de la pièce actuelle et les détails de toute modification par rapport au montage d’origine.

Poser une question sur la compatibilité
Catégories de pièces pour 1981 Honda CB750K

Votre panier

×