VintageCB750, au service des motocyclistes CB depuis 2010

À propos Pourquoi nous choisir? Avis clients Livraison Retours Nous joindre
Favoris
0 Panier

Votre panier est vide.

Parcourir toutes les pièces
Total (USD): $0.00
Voir le panier
Menu
Rechercher
Favoris
Panier 0
Ma moto Choisissez votre modèle Honda CB

Rechercher des pièces

Recherche dans toutes les pièces Honda CB

Exemple : oil filter (filtre à huile) ou une référence OEM.

1974 Honda CB450K — Poignées

Choose the black rubber grip style for your 1974 CB450K after checking the fitted controls. These closed-end factory-style replicas list 135mm length and 7/8-inch bar application. Match the grip’s inside fit over the throttle sleeve and confirm contents before deciding the quantity to purchase.

Fermer ×
Votre moto enregistrée Choisissez votre modèle Honda CB

Magasiner par catégorie

La plupart des commandes sont expédiées le jour ouvrable même ou le suivant Garantie de compatibilité Pièce répertoriée pour votre modèle et votre année? Si elle ne convient pas comme indiqué, nous trouverons une solution. Soutien technique Demandez à notre équipe de vous aider à choisir la bonne pièce Honda CB.
Consultation en cours Poignées

Pièces pour motos Honda

Choisissez votre modèle et l’année pour voir les pièces répertoriées pour votre moto.

Type closed-end grips end detail 53165-342-670

Honda OEM Type Closed-End Grips ~ Replaces 53165-342-670

$17.95 USD
02-2423
Take your early-'70s Honda back to factory spec with these Honda OEM-Type Rubber Grips. Faithful replicas of the original factory grips, in black closed-end...
Comparer

1974 Honda CB450K · Grips Buying guide

Use the replacement references with the fitted control dimensions

Honda 53165-342-670 / 53166-342-670 are the stated grip references. Length, material and end design are described, but exact internal openings and supplied count are not. Compare those missing details when the throttle assembly or accessories have changed.

Parts to consider

Honda OEM Type Closed-End Grips ~ Replaces 53165-342-670 Black 135mm factory-style replica gripsClosed-end rubber option for 7/8-inch bars, referenced to Honda 53165-342-670 / 53166-342-670. Confirm the actual inside fit and what one purchase supplies.Voir la pièce

Check the sleeve-side interface independently

The stated handlebar application does not give an exact inside measurement for the grip fitted over the throttle sleeve. Identify that sleeve’s outside interface and compare the replacement’s required inside fit. Keep the 135mm length in the same assessment, especially where switch housings or throttle components have been changed.

Use explicit contents for a partial grip replacement

Two Honda references identify the intended replacements without establishing a supplied-piece count. Confirm which contents suit the side being renewed and how many pieces one purchase provides. The factory-style replica description also leaves manufacture separate from styling; it does not identify these as Honda-produced original grips.

Buying questions

What information should I obtain before matching grips to a changed throttle sleeve?

Identify the sleeve’s outside fit requirement and available grip length, then obtain the corresponding grip inside dimensions. The listing gives 135mm and 7/8-inch bar application without every internal opening measurement. Compare the fitted sleeve directly instead of using the bar specification as its measurement.

How should I set quantity if only the throttle-side grip is being renewed?

Determine the fit and replacement reference needed for that side, then confirm the supplied contents. The description states two Honda references but no explicit package count. Set the purchase quantity from confirmed contents rather than assuming plural wording guarantees the pieces needed.

What needs comparing before replacing an open-ended grip with this style?

Establish why the existing grip has an opening and how any bar-end accessory attaches. This option is closed-end with stated 135mm length. Compare the retained arrangement before ordering, since the listing does not establish an included accessory opening or clearance for every fitting.

Vous ne savez pas quelle pièce choisir ?

Envoyez-nous le modèle et l’année de votre moto, des photos de la pièce actuelle et les détails de toute modification par rapport au montage d’origine.

Poser une question sur la compatibilité
Catégories de pièces pour 1974 Honda CB450K

Votre panier

×