VintageCB750, au service des motocyclistes CB depuis 2010

À propos Pourquoi nous choisir? Avis clients Livraison Retours Nous joindre
Favoris
0 Panier

Votre panier est vide.

Parcourir toutes les pièces
Total (USD): $0.00
Voir le panier
Menu
Rechercher
Favoris
Panier 0
Ma moto Choisissez votre modèle Honda CB

Rechercher des pièces

Recherche dans toutes les pièces Honda CB

Exemple : oil filter (filtre à huile) ou une référence OEM.

1978 Honda CB400TII — Clignotants, supports, cabochons et réflecteurs

Loose signals and leaking lenses can often be repaired without replacing every lamp. These 1978 Hawk II choices cover a measured front stay, rear mounting rubbers and a matching lens gasket. Identify the installed lamp type before ordering, especially on a restored or customized bike.

Fermer ×
Votre moto enregistrée Choisissez votre modèle Honda CB

Magasiner par catégorie

La plupart des commandes sont expédiées le jour ouvrable même ou le suivant Garantie de compatibilité Pièce répertoriée pour votre modèle et votre année? Si elle ne convient pas comme indiqué, nous trouverons une solution. Soutien technique Demandez à notre équipe de vous aider à choisir la bonne pièce Honda CB.
Consultation en cours Clignotants, supports, cabochons et réflecteurs

Pièces pour motos Honda

Choisissez votre modèle et l’année pour voir les pièces répertoriées pour votre moto.

Honda CB750 CB550 CB500 CB400 CB360 front turn signal stay

Honda CB Front Turn Signal Stay

$12.95 USD
11-2167
Replace a damaged front signal stay with this Front Signal Lamp Stay in chrome. Body length 65mm, thread 25mm, total length 90mm. Pairs with...
Honda CB750 CB500 CB450 CB400 turn signal lamp gasket 33443-268-671

Honda CB Turn Signal Lamp Gasket ~ Replaces 33443-268-671

$4.61 USD
11-2085
Service your early CB750 or classic twin turn signal with this Turn Signal Lamp Gasket, replacing OEM #33443-268-671. Pairs with our signal lens #11-2110...
Honda CB750 CB550 CB450 CB400 rear turn signal rubbers pk 2 33606-371-000

Honda CB750 / CB550 / CB450 / CB400 Rear Turn Signal Rubbers Pk/2 ~ Replaces 33606-371-000

$15.95 USD
73-0834
Replace your rear turn signal rubbers with this Rear Turn Signal Rubbers Pk/2, replacing OEM #33606-371-000. These are the rubbers that go under the...
Comparer

1978 Honda CB400TII Hawk II · Turn Signal Mounts & Seals Buying guide

Match the support and seal to the installed signal

A front stay sets lamp position, rear rubbers support the rear stays, and the lens gasket seals a particular housing. Check those interfaces separately when building a repair order.

Parts to consider

Honda CB Front Turn Signal Stay Chrome front signal stayA 65mm body plus 25mm threaded section gives 90mm overall length. Compare the old stay and lamp attachment; other stay lengths may have been fitted during previous repairs.Voir la pièce Honda CB750 / CB550 / CB450 / CB400 Rear Turn Signal Rubbers Pk/2 ~ Replaces 33606-371-000 Rear signal mounting rubbersPack of two rubbers for the rear signal stays. Each rear signal uses two rubbers, so one pack services one rear mounting position and two packs service both sides.Voir la pièce Honda CB Turn Signal Lamp Gasket ~ Replaces 33443-268-671 Turn signal lens gasketLens gasket using reference 33443-268-671, matched to the corresponding round replacement lamp and lens. Check the lamp assembly itself before choosing a gasket for changed signals.Voir la pièce

Count rear rubbers by mounting position

Each pack contains two rear turn-signal rubbers, and each rear signal uses two. One pack therefore covers one rear stay; replacing both sides calls for two packs. Inspect the stays and surrounding hardware at the same time so the repair is planned around the complete mounting point.

Check lamp identity before buying the seal

The lens gasket is matched to the corresponding round replacement lamp and lens. Signals may have been changed over the years, so compare the housing and sealing face rather than relying only on the motorcycle year. The chrome front stay also needs a length and attachment check against the fitted lamp.

Common buying questions

How many rubber packs do I need for both rear signals?

Order two packs to replace the rubbers at both rear signals. Each pack contains two rubbers, while each rear signal uses two; one pack services one side of the motorcycle.

How long is the chrome front stay?

Its body is 65mm long, with a 25mm threaded section for 90mm overall. Measure the old stay in the same way and compare its lamp attachment before choosing the replacement.

Will the lens gasket fit aftermarket signals?

Only if their lens and housing use the matching gasket pattern. Compare the installed assembly and sealing face first. A shared motorcycle application does not establish that every replacement signal uses the same lens seal.

Vous ne savez pas quelle pièce choisir ?

Envoyez-nous le modèle et l’année de votre moto, des photos de la pièce actuelle et les détails de toute modification par rapport au montage d’origine.

Poser une question sur la compatibilité
Catégories de pièces pour 1978 Honda CB400TII

Votre panier

×