The 1974 CB360K0 uses a cable-operated front drum brake, a rod-operated rear drum and a manual clutch. Start with the system needing attention, then match rear linkage hardware, hand controls or clutch plates to the original assembly.
Rebuild your early SOHC CB's front master cylinder with this Front Brake Master Cylinder Rebuild Kit, replacing OEM #45530-377-305. Made in Japan. Fits the...
Replace a worn silver-with-black-tip clutch lever with this Clutch Lever, a direct replacement for OEM #53178-369-700. Exceptionally broad fitment across the classic Honda lineup,...
Replace your master cylinder rubber boot with this Master Cylinder Rubber Boot, which attaches where the brake hose joins the master cylinder. Replaces OEM...
Replace a hardened or torn master cylinder diaphragm with this Master Cylinder Reservoir Diaphragm, replacing OEM #45520-300-000. Exceptional range of applications, fits FRONT master...
Replace your brake rod spring with this Brake Rod Spring, replacing OEM #95014-73100. Exceptionally broad fitment across the SOHC and DOHC CB750 lineup, CB650...
Replace your brake rod joint with this Brake Rod / Arm Joint, replacing OEM #95015-32001.Key Features• Brake rod / arm joint• Replaces OEM #95015-32001•...
Bring racetrack-inspired ergonomics to your cockpit with this Custom GP-Style Clutch Lever in silver. Features a more pronounced bend/kickback than the stock lever, for...
Replace your master cylinder cap O-ring with this Master Cylinder Reservoir Cap Plastic O-Ring, replacing OEM #45521-MJ6-006.Key Features• Master cylinder reservoir cap O-ring• Plastic•...
Replace your front caliper bleed screw with this Front Brake Caliper Bleed Screw, replacing OEM #45224-579-013.Key Features• Front brake caliper bleed screw• Replaces OEM...
Replace your brake rod joint pin with this Brake Rod Joint Pin with Cotter Pin, replacing OEM #95015-52000 (joint pin) and #94201-16250 (cotter pin).Key...
Replace your brake rod adjusting nut with this Brake Rod Adjusting Nut, replacing OEM #95015-42000.Key Features• Brake rod adjusting nut• Replaces OEM #95015-42000• Honda...
Replace your brake hose grommet with this Brake Hose Rubber Grommet, the rubber grommet that attaches to the brake hose, replacing OEM #45146-300-000.Key Features•...
Replace your front brake caliper piston with this Front Brake Caliper Piston, 38.15mm diameter x 34mm height, replacing OEM #45107-323-020. The side with the...
Upgrade to a universal front master cylinder assembly with this Honda-type unit. Complete with lever, banjo bolt, banjo bolt washers, and brake light switch,...
Replace your rear brake stopper arm strap with this Joker Machine Brand Custom Rear Brake Stopper Arm Strap, replacing OEM #43431-286-010 / #43431-340-000.This strap...
Replace your CB350, CB360, CB350F, or CB400F rear brake shoes with this Rear Brake Shoe Set of 2, replacing OEM #43120-KG4-006.Key Features• Rear brake...
Upgrade your brake rod adjuster knob with this Joker Machine Brand Custom Brake Rod Adjuster Knob, replacing OEM #95015-42000.Gives your bike a great custom...
Replace the brake lever on the #08-0262 Master Cylinder Assembly specifically with this Brake Lever. Designed for this particular master cylinder.Key Features• Replacement brake...
Replace a worn, seized, damaged, or missing front brake caliper with this aftermarket full caliper assembly for Honda CB models. It is a replacement...
Replace your CB500K or CB350/CB360 steel clutch plate with this Steel Clutch Drive Plate "B", replacing OEM #22321-KA4-700.Order the number of pieces required for...
Replace your master cylinder reservoir cap with this Master Cylinder Reservoir Cap with Diaphragm, round OEM thread-on type. Cap replaces OEM #43513-MJ6-006, diaphragm replaces...
Replace the front brake pipe on your small-bore Honda with this Front Brake Pipe, a direct replacement for OEM #45128-317-701. Approximately 8" total length,...
Replace your CB650, CB550, CB350, or CB360 clutch friction plate #1 with this Clutch Friction Plate #1, replacing OEM #22201-286-010.Order the number of pieces...
Replace your CB350 or CB360 steel clutch plate "A" with this Steel Clutch Plate "A", replacing OEM #22311-286-000.1 piece required per bike.Key Features• Steel...
Build a custom front brake setup with this Magura Universal Front Brake Master Cylinder. Features a 13mm piston diameter, 12mm stroke, and a threaded...
Replace a black-finish brake lever on your small-bore classic with this Brake Lever, replacing a range of OEMs (#53175-467-000, #53170-413-670, #53175-402-700, #53175-360-700, #53175-399-700). Fits...
Rear brake linkage, clutch controls and clutch plates serve different jobs. Identify worn components before ordering, especially when a previous owner has changed the front wheel, brake or handlebar controls.
The stock K0 front brake is operated by a cable; hydraulic master cylinders, hoses and calipers belong to a different arrangement. For a motorcycle with a changed front end, identify the fitted brake assembly before selecting replacement components.
Plan clutch work by component
A worn hand lever and worn internal clutch plates call for different purchases. The original clutch contains eight friction discs, seven B-type steel plates and one A-type steel plate. Check the condition and arrangement against the Honda manual before making a parts list.
Common buying questions
Will CB360G disc-brake parts fit my original K0?
The original K0 has a cable-operated front drum. Do not order hydraulic CB360G components as stock K0 replacements. A converted motorcycle needs parts matched to its actual wheel, brake and controls.
Should I buy a lever or clutch plates first?
Inspect the external control and cable operation before dismantling the clutch. A bent lever or worn pivot is a separate repair from internal plate wear; use the service manual to identify the fault.
Are the rear brake joint and adjuster supplied together?
They are separate products. The joint, adjusting nut, spring and joint pin each serve a different place in the rod linkage. Match the missing or worn pieces before ordering.
Not sure which part you need?
Send your model and year, plus photos of your existing part and any changes to the original setup.