Start your 1973 CB450K electrical order at the component you will keep or replace. A coil brings attached leads, a lamp assembly has model-specific mounting requirements, and switch wiring covers a smaller section. Compare each connection before combining these repairs with charging work.
Replace your rear brake light switch with this Rear Brake Light Stop Switch. Exceptionally broad fitment across the SOHC CB750 lineup and virtually the...
Replace your starter motor terminal cover with this Starter Motor Terminal (Cover) Rubber Boot, replacing OEM #32411-230-000.Key Features• Starter motor terminal rubber boot• Replaces...
Restore your mid-'70s Honda's stock reflectors with this Stock-Type Screw-On Reflector with a 6mm thread, replacing OEM #33741-340-670. Broad fitment covering the 1972-78 CB750...
Replace the gasket on your 1972-onward Honda's tail light lens with this Tail Light Lens Gasket, replacing OEM #33709-341-671. Matches the fitment of our...
Fit left-side handlebar controls on your early SOHC CB with this Bar Switch Assembly for the Clutch Side in black, replacing OEM #35250-300-033. Wiring...
Fit the rubber base beneath your stock front reflector with this Stock-Type Front Reflector Rubber Base, replacing OEM #33743-341-670.Key Features• Stock-type front reflector rubber...
Restore headlight mounting with this Headlight Setting Collar, replacing OEM #61304-292-000. Exceptionally broad fitment across the classic Honda lineup, from the SOHC and DOHC...
Replace a damaged or pitted headlamp rim with this Chrome Headlamp Rim, replacing OEM #33101-300-673 / #33101-405-671. Fits all 1969-78 CB750s, select late-model DOHC...
Restore your headlamp trim with this Headlamp Rim & Retainer Assembly, replacing OEM #33101-404-671 / #33121-300-672 / #33153-300-671. Fits the full 1969-78 SOHC CB750...
Replace your late-'70s CB starter solenoid with this Starter Solenoid Relay, replacing OEM #35850-375-000 / #35850-286-027. Broad fitment across the late SOHC CB750, CB500T/CB550...
Replace a worn headlight case collar with this Headlight Case Collar, a direct replacement for OEM #61302-300-000. Located on each side of the stock...
Seal up your starter motor with this Starter Motor Seal, size 60 x 1.4, replacing OEM #31206-286-158 / #31206-402-008. Exceptionally broad fitment across the...
Replace your front stop switch sub harness with this Front Stop / Brake Switch Sub Harness, replacing OEM #35345-319-000.Key Features• Front stop / brake...
Replace your headlight adjuster with this Headlight Adjusting Screw & Spring Set. Each set includes one screw and one spring. Replaces OEM #33103-346-670 (screw)...
Replace the right-side contact point on your CB500T or CB450/CL450 with this Contact Point for the Right Side, replacing OEM #30203-292-003 / #30203-292-154.Key Features•...
Match with the left-side contact point using this Contact Point for the Left Side, replacing OEM #30204-292-003 / #30204-292-154. Same fitment as 14-0007 plus...
Service your early CB750 or classic twin turn signal with this Turn Signal Lamp Gasket, replacing OEM #33443-268-671. Pairs with our signal lens #11-2110...
Replace your CB350, CB360, CB450, or CB500T rectifier with this Rectifier with female connector, replacing OEM #31700-455-671 / #31700-358-305 / #31700-358-013 / #31700-292-008 /...
Restore the classic look of your Honda with this Stock Style Headlight Assembly. Features 7" Halogen Headlight Unit, Headlight Rim & Retainer, Plastic Headlight...
Restore a proper tail end on your classic Honda with this Chrome Tail Light Bracket, replacing OEM #84701-341-670 / #84701-371-980. Fits a wide range...
Universal Motorcycle Spark Plug Cap ~ VB05F is an aftermarket part for the Honda CB applications listed in this product information. Before ordering, confirm...
This aftermarket starter battery cable replaces Honda OEM 32401-319-010 on the listed Honda CB applications. This cable connects the starter/battery circuit and helps carry...
Upgrade your charging system with this Rick's Electric Hot Shot Rectifier/Regulator, replacing OEM #31400-292-670 / #31700-455-671 / #31700-292-008. Combination unit works with the stock...
Upgrade your CB450 or CL450 charging system with Rick's Electric High Performance Hot Shot Charging Kit for standard lead-acid batteries. Includes a new rotor...
Upgrade your CB450, CB500T, CB350, CB360, or small classic with Rick's Electric Hot Shot Lithium Ion Rectifier/Regulator. This combination unit works with the stock...
Compare the supplied component with its surroundings
The coil specifies its primary rating and attached wire lengths. The headlight assembly names a halogen unit, case and trim, with an old-mounting-bolt requirement for CB450K. Front brake-switch wiring has a separate reference. Battery chemistry determines the suitable charging-control version.
Identify changed wiring before ordering by motorcycle year
A previous lamp, ignition or switch replacement may have altered a connector or mounting point. Compare the component now fitted with the replacement’s reference, measurements and named contents. Confirm missing connector details where necessary, rather than treating the motorcycle application as a wiring map.
Keep charging controls consistent with the battery
The lithium control specifies 14V ±0.2 and requires confirmation that this suits the battery. It excludes standard lead-acid batteries; the standard Hot Shot version excludes lithium. If changing battery type, review the charging parts already fitted as well as the version you intend to order.
Connections to check across the electrical order
What should I check when the original headlight bolts are missing?
The assembly’s CB450K instruction calls for the old mounting bolts. Establish the required attachment and replacement fasteners for the retained supports before ordering the lamp. Its general hardware list does not override that model-specific requirement.
Can a battery change affect which charging part I need?
Yes. Standard Hot Shot controls and charging kits are for lead-acid batteries; lithium versions exclude them and specify a 14V ±0.2 set point. Identify the battery and confirm its charging requirement before choosing the control or kit.
How can I check brushes when the starter was replaced?
Identify the actual motor first. The offered set is for Mitsuba two-brush starters, with 12 × 14 × 6mm brushes and one insulated plus one non-insulated lead arrangement. Compare the removed components instead of using the motorcycle year to identify the replacement motor.
Not sure which part you need?
Send your model and year, plus photos of your existing part and any changes to the original setup.